17TR Cykel Keramisk Bearing Kulfiber Jockey remskive sæt bag kædeomskiftere Guide Wheel
Produkt beskrivelse
* 17T stor størrelse guide hjulsæt systemet
*17T pulleys or16T pulleys
* Sparer 60% kæde friktionsmodstand i forhold til 11T styrehjul”
* Keramisk lejetype sparer mere end 2,4 watt gennemsnitlig effekt i forhold til den oprindelige skiftende systemet
* Fuld kulfiber bur
* Fuld 7075 aluminiumslegering CNC skæring letvægts guide hjul og aksel pin
*Color: Anode red, enamel, blue, gold, green
*17TR is suitable for Shimano 6700/6770/6800/6870/9000/9070 Ultegra/DURA ACE
* Keramisk Bearing Version rustfrit stål Hybrid Bearing Version Stål Bearing Version
* Vægt: 61,4 g
* Han keramiske Bearing version er 1,2 gram lettere end stål Bearing versionen
*Shifting speed increased by 20%-26% for Shimano systems.
*Support up to 11-28 cassettes, compatible with 11-30 and 11-34 with the help of an RD extender.
This is the fastest RD pulley system.
17TS & 17TR installation tips:
1, due to increased offset by the oversized pulley system, please make sure your RD and frame are aligned and calibrated correctly.
2, please check the length of your chain. Here is how to calculate, chain should be 10-20mm longer than the RD at 0 tension (shown as the picture below) when rests on the smallest chainring and smallest cog.
3, to lower the requirements for chain length and RD/frame alignment, we introduce the new 16T pulley system, 17TS and 17TR. Compare with 17T, the power saving would be lowered by about 0.2 watts but increasing chain stability and shifting speed.
Hvorfor udskifte bagskifter remskive
For det første kunne porøs fjeder position grænse justere tilbage spænding i vid udstrækning, forbedre svage oprindelige svag strækning, og gøre op og ned kædestramningen mellem føringshjul og tandhjul meget mere passende.
For det andet kontakten tandantal eller kontrol tandantal mellem kæde og tandhjul af bagskifteren 17T er mere under gearskift, det bare gerne klemme på midten og to sider af nogle pinde, jo større kontrol løftestang, jo stærkere kontrol magt.
Endelig efter redesign burets rotation kurve, er afstanden mellem øvre føringshjul og tandhjulene forbedret.
trin installation
1. Bagskifter nedbrydning, fjerne den oprindelige remskive bur, som vist i figuren (oprindelig remskive bur er fjernet, fjernelse metode henvises til figur No.20)
2. Bekræft aluminiumlegeringen ring anderledes sideflade.
3. Den vigtigste bolt pakning.
4. Installer nylon skive til bagskifteren.
5. Montering af hovedbolten pakning i bolten, og anvende fedt.
6. Tag 17T kulfiber remskive bur, bruge No. 2 sekskantnøgle fjerne legering skrues ud på bagsiden af remskive bur.
7. Fjern øvre remskive.
8. Efter fjernelse af øvre remskive, installere midterste bolte på bagsiden.
9. Før installationen hovedbolten skal bolten være fuldt smurt.
10. Skub hovedbolten helt i bunden af remskive bur.
11. Bekræft legeringen ringnoten overflade i hovedbolten, og rille overflade har smurt.
12. Bekræft legeringen ring flyet udad, og legeringen ringen har smurt.
13. Bekræft foråret monteringshul i bagskifteren.
14. Fjederen pin alignment fjeder monteringshullet i bagskifteren.
15. Bekræft fjederpinden ind i bunden af fjederen positionering hul.
16. Installer fjederen.
17. Aligned fjederpinden med hullet på remskive bur
18. Markerede i 1 til 4 er hul spænding justering, standard indledende montering er hul 2. (spænding: 4> 3> 2> 1)
19. remskive bur fuldt presset i bagskifteren. bekræfte hovedbolten tilpasning.
20. No. 4 unbrakonøgle til at stramme hovedbolten til 4N.m.
21. Nulstil øvre styrehjul, indsætte de øvre remskive bolte, men ikke strammet.
22. Rotation af remskive bur til bagskifteren rebound grænse blok, tryk topupper remskive bolt ud, blokerer grænse blok.
23. Spænd øvre remskive bolt.
24. installationen er færdig.
According to test result, increase the rear derailleur pulley wheel size could significantly decrease the friction between the chain plates caused by polygon effects during chain bending, and reduce the resistance for saving rider’s cycling power.
The chain is composed of several short pieces with an inch long, we could see the chain as one inch long with around one hundred and ten section lines, due to small diameter of turning circle, when the lines pass through standard 11T pulley wheel, it needs a certain angle to turn the transferring direction of chain for about 180° through two wheels, after increasing the pulley wheel size, the chain turning angle are decreased, so the loss of friction is less correspondingly. The results shows that 17T is a good balance point between weight and decreasing the polygon effects, To increase the size blindly will lead to arc decreasing not obvious, together with weight and volume adding. Compared with common 11T pulley wheel, the friction loss caused by polygon effects of chain could be decreased about 60%.
Besides, under the same transferring speed of chain, the axis rotation speed of 17T is slower for saving the self friction loss during bearing rotation, smaller cycle could also reduce the resistance of each turn rotation. To upgrade this ceramic bearing saves more power loss.
Faster gear shifts. firstly, porous spring position limit could adjust back tension largely, improve the weakness of original weak stretch, and make the up and down chain tension between guide wheel and cogs much more adequately.
For det andet kontakten tandantal eller kontrol tandantal mellem kæde og tandhjul af bagskifteren 17T er mere under gearskift, det bare gerne klemme på midten og to sider af nogle pinde, jo større kontrol løftestang, jo stærkere kontrol magt.
Endelig efter redesign burets rotation kurve, er afstanden mellem øvre føringshjul og tandhjulene forbedret.
And we should also tell customer that the compatibility of 11-28T cogs, the length of chain is within the range of 405-410mm standard road bike chain stay, suggest using more than 114 links, but not too short chain, or it might lead to too large back tension and enlarge the tooth tip resistance between chain and pulley wheels. (In case customer just has short chain, suggesting install it to lowest tension of spring mounting hole).
It can faster SHIMANO system up and down gear to improve 20%-26%. save 2.4 watts more.
